Macrosystem Bogart SE Ver.2 User manual Manuel d'utilisateur télécharger pdf (Page 8)

100

Chapter 2

displayed in the System Settings screen.

If your system runs a current version, you can start editing di-

rectly. If the version number of the CD/DVD is higher, then you

should install the more recent version.

You must carry out the installation procedure if you do not see

the Main Menu screen once your system is turned on.

2.3.1 Installing from CD/DVD

The Bogart SE installation is always started from CD, there

is no other possibility. The process is controlled using track-

ball/mouse. The installation is monitored via SCART or DVI,

depending on the last selected monitor (when using a new

hard-drive, VGA). You can use the `v´ button to switch between

the monitor outputs. Press the `v´ button until the correct moni-

tor is shown. At the same time, the installation menu is always

diplayed via VGA.

There are two methods of installing Bogart SE, either as a full

installation or as an update. Follow these steps to install:

The CD/DVD used to install Bogart SE is a so-called `boot

medium´, meaning that the process is not started from the

`Install product´ menu, but instead it is installed by inserting the

medium into the drive and then restarting the editor (starting a

system is often called `booting´).

To insert the CD/DVD, power up the editor. If your device is

already pre-installed with a system software, please wait until it

has fully powered up and is ready for operation. Open the CD/

DVD tray using the eject button on the front panel of the editor.

Starting an `empty´ system without any system software (if you

are using a new hard-drive for instance), the installation is a

little different: Power up the device and press the eject button

a few times. The tray will open and you can insert the medium.

Now close the tray using the eject button. In some cases, the

tray may re-open – simply power down the editor if this is

the case. To do this, press the OK and ON/OFF buttons (on

the front) at the same time for about 4 seconds. The system

will now switch off.

Now restart the device. The editor will `boot´ from the CD/DVD

and you will be prompted to follow the on-screen instructions.

The installation is available in German or English language.

Screen output is available for video and DVI screens. To make

a change to the settings, press the `arrow up´ key on the front

panel. This is only possible in the ﬁrst few menus and only

makes sense right here. If you do not see a picture after the

installation, the screen output may have been switched to an

unused screen. In this case, press the `arrow up´ button to

switch to the alternative screen.

Generally, you will ﬁnd information about setting up in each

menu. At the bottom of the screen you will also see a graphical

display of the front panel buttons in symbol form. The active

buttons are shown in a brighter tone.

The installation begins with a language selection: English or

German. Press the respective symbol key to select. You can

also choose between SCART and DVI at this point.

After the language selection, the hardware will be analysed.

Without a prior installed Bogart SE system software, only a full

installation will be possible. With a previous Bogart SE installa-

tion already on the hard-drive, the installation will automatically

offer to proceed with an update. If you wish to go ahead with

a full installation instead, use the front buttons to make the

change. This menu also allows you to switch between SCART

and DVI.

Once you have decided on the installation type, the installa-

tion will begin. In the meantime, a progress bar will be shown.

When done, you will be informed if the installation was suc-

cessful. In any case, the DVD tray will open automatically and

you will be asked to remove the medium. Press the OK

key to close the tray and end the installation.

The installation is now completed. Restart the device to begin

working with Bogart SE.

Note : Should a problem occur during the installation, you may

wish to retry installing. Leave the medium in the tray and end

the installation with OK. Now restart the editor to begin a new

installation.

When you start the device again, it will take a few moments

until all required data is loaded. The Bogart main menu will

then appear. This menu is like the control centre of Bogart.

From here, you can initiate all the different parts of the video

editing process. The startup phase is now complete, you can

begin editing.

1 2 3 4 5 6 7 8 9 10 11 12 13 ... 99 100

Commentaires sur ces manuels

Pas de commentaire

Macrosystem Bogart SE Ver.2 User manual Manuel d'utilisateur Page 8

Commentaires sur ces manuels

Produits connexes et manuels pour Logiciel Macrosystem Bogart SE Ver.2 User manual